Sidewall Conveyor Belt Retrofit Enters Installation at Coal Chemical Plant

QBF rubber is on site at a coal chemical plant, installing a corrugated sidewall conveyor belt as part of a retrofit. The belt it replaces had worn unevenly and run off-centre for most of its service life. The new specification was not picked from a catalogue. It came out of a survey of the conveyor that carries it.

측벽 컨베이어 벨트 설치

Where the problem actually sat

Before a belt was quoted, QBF rubber engineers walked the line end to end. They looked at the material and how it behaves in the trough, at the belt path and the transitions, at skirt clearance. Idlers and pulleys were checked too, along with the shape they were in.

The picture that came back was consistent. The belt was worn, yes. It was also the wrong belt for the duty. A belt that does not match its line will run off-centre, and once it runs off-centre, wear concentrates in a few places and speeds up there. Correct the tracking alone and the wear comes back.

Chemical corrugated sidewall conveyor belt

The new specification: B1400 S300 TC280, flame-retardant K3

The replacement belt is specified as B1400 S300 TC280, flame-retardant K3. The figures were set during the survey, not taken off a stock list, and they match the duty this line actually runs.

Width, wall height and base stiffness follow the material, the incline and the geometry of the conveyor. On this line they were set during the survey, then checked against the duty the belt actually runs.

 

QBFRUB~1

Splices made on site, then commissioning

The belt is joined on site by hot vulcanization, not with mechanical fasteners. The splice is pressed and cured under heat on the line itself. On a sidewall belt the wall and cleats are cured with the splice, so the wall runs continuous through the joint instead of breaking at every connection.

Commissioning follows the splicing. Tracking is corrected, tension is set, and the belt is run before material goes on it.

Belt changes are shutdown work at a coal chemical plant. What this project is after is a line that tracks straight, wears evenly, and a next change that can be scheduled rather than forced.

Sidewall Conveyor Belt hot vulcanization

태그:
화신 관리자

제품

스틸 코드 베이스 벨트

베이스 벨트

일반 벨트와 달리 당사의 베이스 벨트는 횡방향 강성을 강화하여 굴곡 지점에서의 변형을 방지하는 동시에 종방향 유연성을 유지하여 풀리 주변에서 원활한 작동을 보장합니다. 국제 표준(DIN/ISO/EN)에 따라 엄격하게 제조된 당사의 베이스 벨트는 까다로운 벌크 자재 처리 환경에서도 장기적인 안정성과 신뢰할 수 있는 성능을 보장합니다.
측벽

측벽

이 강화 측벽은 고급 고무 컴파운드와 통합된 직물 보강 구조를 특징으로 하여 굴곡 피로 저항성을 향상시키고 골형 균열을 방지합니다. 동적 피로 시험을 통해 검증되었으며, 다양한 고무 특성과 여러 가지 표준/맞춤형 크기를 제공하여 복잡한 작업 환경에서도 안정적인 장기 성능을 보장합니다.
세라믹 풀리 래깅

풀리 래깅

고성능 세라믹 풀리 라이닝은 벨트 미끄러짐, 빠른 마모, 이물질 축적 및 풀리 수명 단축 문제를 해결합니다. 냉간 접착 방식이므로 공장 열가황 처리 없이 현장에서 설치가 가능합니다. 92% 알루미나 세라믹 타일과 고무 백킹의 조합으로 광산, 채석장 및 항만 벌크 자재 처리 분야에서 습하고 진흙탕인 환경에서도 탁월한 마찰력을 제공합니다.
고무 마모 라이닝 05

고무 내마모 라이닝

당사의 고무 마모 방지 라이닝은 산업 장비 내부용으로 설계된 고강도 보호 고무층입니다. 탁월한 내마모성, 내충격성 및 내식성을 자랑하며, 분쇄기, 슈트 및 호퍼를 장기간의 자재 마모로부터 효과적으로 보호합니다. 가볍고 내구성이 뛰어나며 완벽한 맞춤 제작이 가능하여 유지보수 비용을 절감하고 소음을 줄여주므로 광업, 시멘트 및 화학 산업 분야에 이상적입니다.
측벽 컨베이어 벨트

측벽 컨베이어 벨트

QBF Rubber는 항만, 야금, 터널, 발전소, 화학, 시멘트, 지하철 등 다양한 산업 분야에서 벌크 자재 이송에 사용되는 고품질 급경사 컨베이어 벨트의 설계 및 제조를 전문으로 합니다. 유럽식 금형과 표준을 완벽하게 사용하는 유일한 중국 제조업체인 QBF Rubber는 벨트 선정, 생산, 설치, 시운전 및 문제 해결에 이르는 완벽한 솔루션을 제공합니다.
EPDM 고온 측벽 컨베이어 벨트

EPDM 고온 측벽 컨베이어 벨트

맞춤형 EPDM 고온 측벽 컨베이어 벨트는 300℃의 순간적인 열충격을 견뎌냅니다. 시멘트, 야금, 발전소의 고온 벌크 자재 이송에 이상적입니다.
저희에게 연락하세요

저희에게 연락하세요

    제품
    콘택트 렌즈
    왓츠앱
    이메일